|
C5 Open Discussion General and technical C5 Corvette discussion - ownership, maintenance, repairs, modifications, tuning |
|
Share | Thread Tools | Search this Thread |
04-06-2010, 7:58am | #1 | ||||||
Vette Barn Regular
Join Date: Jan 2010
Location: Chesapeake
Posts: 61
Thanks: 17
Thanked 11 Times in 10 Posts
Gameroom Barn Bucks: $882
|
Quicktime SFI Bellhousing Install
As part of my driveline freshen up, I added a Quicktime SFI approved bellhousing. The benefit of one of these is only realized in the event of a clutch or flywheel failure, the idea being that the high strength steel bell will keep the shrapnel from cutting your feet off! That may be a little dramatic, but if you google clutch explosion you'll see the destruction that can be caused. It aint pretty.
Here's a shot of the bellhousing being test fit to the end of the torque tube. This isnt a straightforward install, as the bellhousing flange is circular to start with and must be trimmed to clear header tubes. I also trimmed a fair amount off the bottom as it would be the lowest point of the car by an inch or more otherwise. The flange is thick steel, a plasma cutter is your best bet if you have access to one. The dashed line shows where the flange used to be. Also in need of attention is the notch for the clutch slave bleeder. The bellhousing will not clear an aftermarket clutch bleeder line (it barely clears the stock screw). The dashed line indicates the additional clearance that was required.
__________________
99 FRC - A&A T-Trim @ 10PSI |
||||||
The Following User Says Thank You to FRC Joe For This Useful Post: |
04-06-2010, 8:47am | #2 | ||||||
Charter Member
Join Date: Oct 2009
Location: Virginia Beach
Posts: 1,700
Thanks: 43
Thanked 213 Times in 162 Posts
Gameroom Barn Bucks: $8830
|
Is that a C5/C6 specific part or does it have other applications? If it's a C5/C6 part why in the world would they not do the R&D to deliver it in a proper for so you don't have to make any modifications?
|
||||||
04-06-2010, 9:00am | #3 | ||||||
A Real Barner
Join Date: Oct 2009
Location: Lackey/Yorktown, VA
Posts: 2,088
Thanks: 512
Thanked 1,705 Times in 588 Posts
Gameroom Barn Bucks: $1005893
|
Nice Joe, Just saw one 4 sale on the CF
|
||||||
04-06-2010, 9:02am | #4 | ||||||
Vette Barn Regular
Join Date: Jan 2010
Location: Chesapeake
Posts: 61
Thanks: 17
Thanked 11 Times in 10 Posts
Gameroom Barn Bucks: $882
|
As far as I know it's C5/C6 specific. If I had to guess I'd say that QT figures that by the time someone is putting one of these on their car, there's no telling what else they've done to it. And that providing maximum material allows for trimming to individual applications while retaining maximum strength.
__________________
99 FRC - A&A T-Trim @ 10PSI |
||||||
04-06-2010, 9:28am | #5 | ||||||
Charter Member
Join Date: Oct 2009
Location: Virginia Beach
Posts: 1,700
Thanks: 43
Thanked 213 Times in 162 Posts
Gameroom Barn Bucks: $8830
|
Yeah, but the fact is that as delivered you can't even install headers! How many people who would need/want that bit wouldn't run LT headers.... just seems odd to me.
__________________
2001 Quicksilver Z06 - NASA PTA/TTA/ST2 #4 www.carsandcoffeevirginiabeach.com April 7th, 2012 7:30am-9:30am @ La Promenade |
||||||
|
|
Support the Barn: |
Download the Mobile App; |
Follow us on Facebook: |
||