The Vette Barn

The Vette Barn (https://www.thevettebarn.com/forums/index.php)
-   C5 Open Discussion (https://www.thevettebarn.com/forums/forumdisplay.php?f=15)
-   -   Aftermarket Seat owners - Color matching BLACK carpet for the feet of seat brackets. (https://www.thevettebarn.com/forums/showthread.php?t=9492)

Toque 03-04-2011 10:45am

Aftermarket Seat owners - Color matching BLACK carpet for the feet of seat brackets.
 
Guys:

Ever since I installed my Corbeau A4's (and Corbeau seat brackets) I have been left with an empty spot around the mounting feet. Its a big bare floor "Silver" spot around all the mounting feet where there is no carpet. I have wanted to find some carpet or something to cover it up. The factory seat brackets have a plastic cover to cover this bare carpet area.

While reading the forums I found a post where he made his own partition and put carpet on it. I asked him if the color was close to factory and he said it was very close in color. He got it at Walmart for $9.

I went to Walmart Wed night and got some of this carpet. Its a little thinner than the factory carpet but the color is surprisingly perfect. I was surprised how close a match it was.

I lifted my seats, then cut 8x square pieces of this carpet (6"x6"), then cut a hole in the middle for the bolt to go thru. I was able to slip this carpet square under the existing carpet easily.

You can now barely see where the factory carpet ends and this carpet starts. :hurray:

Gives it a "finished" look that I wanted. It matches ALOT better than the expensive Lloyd mats I have... seriously !

Walmart Item # 15524364 (under $9).

Hope this helps someone... :)

Toque

http://mysite.verizon.net/res0aae8/temp/carpet.jpg

WKMCD 03-04-2011 11:20am

Looks good! I had some black carpet that I used on a board to cover the amps behind the bulkhead. I cut a couple small pieces and did the same. The insulation you and I put in really made the hole stand out.

Toque 03-04-2011 11:31am

Quote:

Originally Posted by WKMCD (Post 174386)
Looks good! I had some black carpet that I used on a board to cover the amps behind the bulkhead. I cut a couple small pieces and did the same. The insulation you and I put in really made the hole stand out.

Thanks !

The insulation you and I put in ? What insulation is that ?
Under my carpet is bare balsa wood... :D

I don't need no stinking sound deadening... :rofl:

Toque

Bucwheat 03-04-2011 11:47am

Pretty cool!

Eagleeye 03-08-2011 8:57pm

Looking at those seats but I have 39-40 waist...5'11" and 198 lbs. What do you think ? I've been told it might be too snug ?

WKMCD 03-08-2011 9:28pm

Quote:

Originally Posted by Toque (Post 174402)
Thanks !

The insulation you and I put in ? What insulation is that ?
Under my carpet is bare balsa wood... :D

I don't need no stinking sound deadening... :rofl:

Toque

Big motors make a lot of heat...:rofl:

Toque 03-09-2011 12:04am

Quote:

Originally Posted by Eagleeye (Post 181542)
Looking at those seats but I have 39-40 waist...5'11" and 198 lbs. What do you think ? I've been told it might be too snug ?

I'm 38" waist.... 6ft, and 210lbs.

I sure don't want to gain any weight... :rofl:

I'm snug in them ... but not overly. I just don't want to get any bigger or it might get uncomfortable.

Toque


All times are GMT -5. The time now is 6:15am.

Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
User Alert System provided by Advanced User Tagging (Pro) - vBulletin Mods & Addons Copyright © 2024 DragonByte Technologies Ltd.
Copyright © 2009 - 2024 The Vette Barn