|
C6 Open Discussion General and technical C6 Corvette discussion - ownership, maintenance, repairs, modifications, tuning |
|
Share | Thread Tools | Search this Thread |
02-16-2011, 10:10pm | #1 | ||||||
Charter Member
Barn Stall Owner #22
Join Date: Oct 2009
Location: South Korea
Posts: 1,961
Thanks: 158
Thanked 292 Times in 181 Posts
Gameroom Barn Bucks: $8878
|
Check your nuts
A few months after I bought my Vette I noticed some noises in the rear and found out my axle nut was loose, if memory serves me right I torqued to 120lbft. Its been a few months since I last checked and I decided to check them today to make sure they were still tight (they were), then I thought I would pass on to the VB as the C6's are known to have loosening axle nuts for some.
There is debate on how much torque to use, I went with 120lbs, the Chevy document below mentions 160lbft. Another helpful tip, if using locktite, use blue, not red. I didn't need to use locktite or order a new nut as the Chevy doc recommends, but I check them a couple times a year to make sure they are tight. Document ID# 2018487 2005 Chevrolet Corvette -------------------------------------------------------------------------------- Subject: Tapping or Scraping Noise From Rear Wheel Area (Replace Wheel Drive Shaft Nut) #07-04-95-001 - (09/26/2007) Models: 2005-2008 Cadillac XLR 2005-2008 Chevrolet Corvette -------------------------------------------------------------------------------- Condition Some customers may comment on a tapping or a scraping noise coming from the rear wheel area. Cause This condition may be due to the torque on the wheel drive shaft nut relaxing over time. Correction Replace the left and the right wheel drive shaft nut following the procedure below. Remove the center cap from the rim. Remove and discard the wheel drive shaft nut. Apply LOCTITE™ 272, or equivalent, to the threads of the axle shaft. Install the nut and tighten to the new specification. Tighten Tighten the nut to 215 N·m (160 lb ft). Install the center cap to the rim. Important: The vehicle should not be driven for 24 hours following the repair in order to allow the thread lock to cure. Parts Information Part Number Description Qty 10257766 Nut 2 (one per side) Warranty Information For vehicles repaired under warranty, use: Labor Operation Description Labor Time F9712* Wheel Drive Shaft Nut - Replace 0.3 hr *This is a unique labor operation for bulletin use only. It will not be published in the Labor Time Guide. GM bulletins are intended for use by professional technicians, NOT a "do-it-yourselfer". They are written to inform these technicians of conditions that may occur on some vehicles, or to provide information that could assist in the proper service of a vehicle. Properly trained technicians have the equipment, tools, safety instructions, and know-how to do a job properly and safely. If a condition is described, DO NOT assume that the bulletin applies to your vehicle, or that your vehicle will have that condition. See your GM dealer for information on whether your vehicle may benefit from the information. WE SUPPORT VOLUNTARY TECHNICIAN CERTIFICATION © Copyright General Motors Corporation. All Rights Reserved. -------------------------------------------------------------------------------- Document ID# 2018487 2005 Chevrolet Corvette |
||||||
The Following User Says Thank You to thegreenman For This Useful Post: |
02-17-2011, 11:19am | #2 | ||||||
Vette Barn Regular
Barn Raising I
Join Date: Oct 2009
Location: Wichita Falls, Texas
Posts: 213
Thanks: 1
Thanked 126 Times in 63 Posts
Gameroom Barn Bucks: $1729
|
You might want to look into this little item that has been used on the ZR1 axles since 2009. Nord-Lock - Products
I put them on my '10 Z06 and the nuts have never backed off. You can pick them up at a Fastenal store. |
||||||
The Following User Says Thank You to itsaz For This Useful Post: |
02-17-2011, 12:50pm | #3 | |||||||
Charter Member
Barn Stall Owner #22
Join Date: Oct 2009
Location: South Korea
Posts: 1,961
Thanks: 158
Thanked 292 Times in 181 Posts
Gameroom Barn Bucks: $8878
|
Quote:
|
|||||||
03-10-2011, 11:29pm | #4 | |||||||
Vette Barn nOOb
|
Quote:
|
|||||||
04-24-2011, 1:33pm | #5 | ||||||
Vette Barn Crew
Join Date: Jan 2010
Location: Tulsa,Ok
Posts: 109
Thanks: 5
Thanked 13 Times in 9 Posts
Gameroom Barn Bucks: $13
|
Great heads heads up, Thanks.
|
||||||
05-04-2011, 10:29pm | #6 | |||||||
Vette Barn nOOb
Join Date: Feb 2011
Location: Las Vegas, NV
Posts: 25
Thanks: 1
Thanked 3 Times in 2 Posts
Gameroom Barn Bucks: $627
|
Quote:
|
|||||||
|
|
Support the Barn: |
Download the Mobile App; |
Follow us on Facebook: |
||