|
Off Topic Off Topic - General non-Corvette related discussion. |
|
Share | Thread Tools | Search this Thread |
10-17-2019, 10:40pm | #1 | ||||||
A Real Barner
Join Date: Jan 2011
Location: Woodland, CA
Posts: 12,498
Thanks: 7,738
Thanked 5,588 Times in 1,985 Posts
Gameroom Barn Bucks: $1524159
|
What's inside a Tesla motor?
A lot of electronics and I wasn't expecting all that tech inside of it.
|
||||||
The Following 4 Users Say Thank You to Wathen1955 For This Useful Post: |
10-18-2019, 2:40am | #2 | ||||||
Latin American Goat Roper
Barn Stall Owner #101 Bantayan Kids '13
Join Date: Nov 2009
Location: Orange Park Florida
Posts: 60,680
Thanks: 32,874
Thanked 11,544 Times in 5,694 Posts
Gameroom Barn Bucks: $1138393
|
Watt did I miss?? seen the 3 'phase' electronic assembly, but missed the armature that had to be in the middle of it, seems like a lot of crap to avoid a set of brushes.....the gear reduction is about what I expected......
no serious explanation of watt makes the actual motor run, |
||||||
10-18-2019, 8:03am | #3 | ||||||
Chief Meat Gazer
Charter Member Barn Stall Owner #98 Barn Raising II,III,IV
Join Date: Oct 2009
Location: Ohio
Posts: 50,992
Thanks: 23,421
Thanked 33,847 Times in 12,333 Posts
Gameroom Barn Bucks: $5135124
|
|
||||||
10-18-2019, 9:49am | #4 | |||||||
Administrator
Barn Stall Owner #7 Barn Raising I,II,IV NCM Supporter '13,'14
Join Date: Oct 2009
Location: Pewaukee,WI
Posts: 8,217
Thanks: 1,044
Thanked 5,025 Times in 2,238 Posts
Gameroom Barn Bucks: $30682687
|
Quote:
At about the 4:20 mark, you can see them remove the end cover of the actual motor and spin the rotor around within the stator. Then they tear into the opposite end, which houses the inverter (the electronics necessary to convert DC into 3 phase AC current), and finally they open up the gearbox which is sandwiched between the motor and inverter. After they got the gearbox opened (pause it at 10:14), it appears they could have just removed those 3 bearing retainer screws and slid the rotor out of the stator...But they didn't go that far. |
|||||||
The Following User Says Thank You to Y2Kvert4me For This Useful Post: |
10-18-2019, 11:07am | #5 | ||||||
Latin American Goat Roper
Barn Stall Owner #101 Bantayan Kids '13
Join Date: Nov 2009
Location: Orange Park Florida
Posts: 60,680
Thanks: 32,874
Thanked 11,544 Times in 5,694 Posts
Gameroom Barn Bucks: $1138393
|
Yeh, pardon my old so-fist-ic-ated ass, but I wanted to see the windings and rotor of the actual motor, and get an idea of just how it changes speeds, I ASSume by varying the freq of the input power....from looks of the 3 pin spade lugs there, the windings are about 1/4 inch thick, copper I would ASSume....
reading up on my friend's solar panels, and the theory/practice of the power panels they use some ....shit,...can't think of the name/type of transistor/control device, but it's forward voltage drop is about zero at silly high amp/current levels....like .5 volt....... so the same I ASSume for the control device, just that it seems like awful massive for the heat sinks on their main power control switches,.....by comparison that is..... |
||||||
10-19-2019, 8:56am | #6 | ||||||
2016 Election Expert
Barn Stall Owner #64
Join Date: Jan 2011
Location: Joplin, MO
Posts: 18,039
Thanks: 999
Thanked 10,155 Times in 4,727 Posts
Gameroom Barn Bucks: $11380138
|
Yes, three phase AC induction motors alter the frequency of the AC to control speed. There are quite a few advantages to them versus DC motors. They are mechanically simple except for the control electronics. As long as the electronics are robust (i.e. over-engineered) then there's not much to go wrong. Bet there are some big ole mosfets in that control module.
|
||||||
10-19-2019, 10:10am | #7 | |||||||
Latin American Goat Roper
Barn Stall Owner #101 Bantayan Kids '13
Join Date: Nov 2009
Location: Orange Park Florida
Posts: 60,680
Thanks: 32,874
Thanked 11,544 Times in 5,694 Posts
Gameroom Barn Bucks: $1138393
|
Quote:
but the current is much higher off that battery than some individual small panel on a house......so I"d imagine a hell of a stout transistor and heatsink.... |
|||||||
10-19-2019, 12:05pm | #8 | ||||||
Barn Stall Owner #55
Island14 Cardio Team
Join Date: Jan 2011
Location: A sympathetic, well-meaning, elderly man with a poor memory
Posts: 14,736
Thanks: 3,746
Thanked 9,186 Times in 4,360 Posts
Gameroom Barn Bucks: $23236
|
Damn. Never opened the business end of that beast! Would've been nice to see the motor and not just the gearbox and electronics.
|
||||||
The Following User Says Thank You to ZipZap For This Useful Post: |
Thread Tools | Search this Thread |
|
|
Support the Barn: |
Download the Mobile App; |
Follow us on Facebook: |
||