|
Off Topic Off Topic - General non-Corvette related discussion. |
|
Share | Thread Tools | Search this Thread |
10-26-2019, 7:57pm | #1 | ||||||
Barn Stall Owner #327
NCM Supporter '16,'17,'19,'20 Bantayan Kids '13,'14,'15,'17 GTMS 18
Join Date: Jan 2011
Location: Zionsville,PA
Posts: 49,035
Thanks: 25,745
Thanked 21,856 Times in 8,891 Posts
Gameroom Barn Bucks: $5976008
|
New milling vise and made an adjustable stop for it
I picked up a "new to me" Kurt milling vise off ebay for a good price. It's a 4" vise, US made and high quality. Brand new this vise goes for $650 ( I paid a LOT less )
Only a couple "oops" that will not have any negative results in operation. First pics are of the vise. Great clamping power and I can put the jaws on either side of both the stationary or movable jaws. I can also use "soft jaws" with are machined with steps or reliefs for specific jobs. The stop I made is similar to factory offered stop but a whole lot cheaper since I made it ( Almost $110 ) Milled a flat on the bar so it would sit against the back and then drilled the holes for mounting it. I used the drill bit to make sure it was perpendicular when I turned the bar over to mill the bolt flats. The round piece has #10-32 pinch bolts to hold the part in place when tightened. The "blank" arm still needs to have a drilled and tapped hole put in it for a piece of all thread so I can reach inside the vise. The round bar can also be positioned under the back bar for extra clearance. |
||||||
The Following 9 Users Say Thank You to JRD77VET For This Useful Post: |
10-27-2019, 2:35am | #2 | ||||||
Latin American Goat Roper
Barn Stall Owner #101 Bantayan Kids '13
Join Date: Nov 2009
Location: Orange Park Florida
Posts: 60,581
Thanks: 32,797
Thanked 11,529 Times in 5,686 Posts
Gameroom Barn Bucks: $1138393
|
I have a cheep drill press some vice for it, since the 70's yet......made all sorts of shit with it......
|
||||||
10-27-2019, 7:30am | #3 | ||||||
Bantayan Kids '17
Join Date: Mar 2014
Location: Long Valley, NJ
Posts: 2,464
Thanks: 1,113
Thanked 996 Times in 529 Posts
Gameroom Barn Bucks: $406058
|
Nice work. I have no knowledge of metal machining work other than my high school machine shop class; what's the purpose of the "stop" that you added?
|
||||||
10-27-2019, 8:07am | #4 | ||||||
Sparkles Flambeaux
Barn Stall Owner #4 Barn Raising I,II NCM Supporter '13,'14,'15,'16,'17,'21 Bantayan Kids '13,'14,'15,'17
Join Date: Jan 2011
Location: Santa Fe, NM
Posts: 61,433
Thanks: 11,767
Thanked 32,997 Times in 14,148 Posts
Gameroom Barn Bucks: $17500122
|
Oooohhhh, shiney!!!
|
||||||
The Following User Says Thank You to DAB For This Useful Post: |
10-27-2019, 6:37pm | #5 | |||||||
Barn Stall Owner #327
NCM Supporter '16,'17,'19,'20 Bantayan Kids '13,'14,'15,'17 GTMS 18
Join Date: Jan 2011
Location: Zionsville,PA
Posts: 49,035
Thanks: 25,745
Thanked 21,856 Times in 8,891 Posts
Gameroom Barn Bucks: $5976008
|
Quote:
I made another shorter round bar for the stop. I used the stop I just made as I drilled and tapped the hole at the far left. I took the part out of the vise, turned it 90* and put it back against the stop. That kept me from edge finding the part everytime I took it out. |
|||||||
The Following 2 Users Say Thank You to JRD77VET For This Useful Post: |
10-27-2019, 6:52pm | #6 | |||||||
Sparkles Flambeaux
Barn Stall Owner #4 Barn Raising I,II NCM Supporter '13,'14,'15,'16,'17,'21 Bantayan Kids '13,'14,'15,'17
Join Date: Jan 2011
Location: Santa Fe, NM
Posts: 61,433
Thanks: 11,767
Thanked 32,997 Times in 14,148 Posts
Gameroom Barn Bucks: $17500122
|
Quote:
|
|||||||
10-27-2019, 7:06pm | #7 | ||||||
Barn Stall Owner #327
NCM Supporter '16,'17,'19,'20 Bantayan Kids '13,'14,'15,'17 GTMS 18
Join Date: Jan 2011
Location: Zionsville,PA
Posts: 49,035
Thanks: 25,745
Thanked 21,856 Times in 8,891 Posts
Gameroom Barn Bucks: $5976008
|
With the picture above. "X" is left side and "Y" is center of part
( "X" is left right and "Y" is front / back) 1st operation Move "X" to .156 Spot, drill clearance for 10-32 screw half way down. Drill rest of the way thru with tap drill. Tap thru 2nd op Take part out and rotate away 90* Move "X" to .594 spot, drill and open hole to 5/8" 3rd op Take part out and roll away additional 90* ( 180* total) Move "X" to 1.281 spot, drill and open hole to 5/8" 4th op Take part and rotate away additional 90* ( 270* total ) Move "X" to 1.719 spot, drill clearance half way down. Drill and tap 10-32 ~~~~~~~~~~~~ Each time I take the part out, I have to clean chips from the bottom of the vise. The stop allows me to put the part back in the exact same spot in the vise each time. It also works if I am doing multiple parts like the flat bar in the earlier pictures. I usually do 10 at a time. I will drill all of them doing the first hole. then I would move to the second coordinate and drill that hole. Then move to the final coordinate and drill the final hole. Make more sense now? |
||||||
10-27-2019, 8:46pm | #8 | ||||||
Sparkles Flambeaux
Barn Stall Owner #4 Barn Raising I,II NCM Supporter '13,'14,'15,'16,'17,'21 Bantayan Kids '13,'14,'15,'17
Join Date: Jan 2011
Location: Santa Fe, NM
Posts: 61,433
Thanks: 11,767
Thanked 32,997 Times in 14,148 Posts
Gameroom Barn Bucks: $17500122
|
Its a fancy jig. |
||||||
The Following User Says Thank You to DAB For This Useful Post: |
10-27-2019, 8:52pm | #9 | ||||||
Barn Stall Owner #327
NCM Supporter '16,'17,'19,'20 Bantayan Kids '13,'14,'15,'17 GTMS 18
Join Date: Jan 2011
Location: Zionsville,PA
Posts: 49,035
Thanks: 25,745
Thanked 21,856 Times in 8,891 Posts
Gameroom Barn Bucks: $5976008
|
|
||||||
The Following User Says Thank You to JRD77VET For This Useful Post: |
11-21-2019, 8:29pm | #10 | ||||||
A Real Barner
Join Date: Jan 2011
Posts: 2,960
Thanks: 1,859
Thanked 5,728 Times in 770 Posts
Gameroom Barn Bucks: $1007440
|
Is purdy!!
|
||||||
The Following User Says Thank You to WOEII For This Useful Post: |
11-21-2019, 8:33pm | #11 | ||||||
Barn Stall Owner #17
Barn Raising II NCM Supporter '12,'14,'15,'16,'17,'19 Bantayan Kids '13,'14,'15,'17 GTMS 18
Join Date: Jun 2011
Location: PA/FL
Posts: 16,379
Thanks: 3,721
Thanked 8,104 Times in 4,238 Posts
Gameroom Barn Bucks: $10510030
|
Great work on the stop; that is a sexy vise
Scott
__________________
Vette-less but not without toys |
||||||
The Following User Says Thank You to simpleman68 For This Useful Post: |
Thread Tools | Search this Thread |
|
|
Support the Barn: |
Download the Mobile App; |
Follow us on Facebook: |
||