|
Off Topic Off Topic - General non-Corvette related discussion. |
|
Share | Thread Tools | Search this Thread |
05-25-2019, 7:10pm | #1 | ||||||
Barn Stall Owner #327
NCM Supporter '16,'17,'19,'20 Bantayan Kids '13,'14,'15,'17 GTMS ‘18
Join Date: Jan 2011
Location: Zionsville,PA
Posts: 49,142
Thanks: 25,812
Thanked 21,887 Times in 8,906 Posts
Gameroom Barn Bucks: $5976008
|
Cub Cadet part save
George on the cub cadet forum had a major bearing failure for the chain drive tensioner on his snow thrower. Both needle bearings in the ears completely gave up, the sprocket shifted over into the casting and then the chained jumped off the sprocket. Sometime during the event, the spirol pin sheared.
We both looked for a replacement casting but they are next to impossible to find. I got the piece and used my three ton press to get it apart. ( just barely, I thought I would have to do it at work ). I made a bronze contoured washer to fit in the spot where the sprocket abraded the aluminum away and was able to save the transfer shaft. New needle bearings and a new sprocket and now it's ready for next winter |
||||||
The Following 10 Users Say Thank You to JRD77VET For This Useful Post: |
05-25-2019, 7:20pm | #2 | ||||||
A Real Barner
Join Date: Jan 2011
Posts: 2,330
Thanks: 175
Thanked 664 Times in 389 Posts
Gameroom Barn Bucks: $930358
|
neato
|
||||||
The Following User Says Thank You to SubZero For This Useful Post: |
05-25-2019, 9:17pm | #3 | ||||||
Barn Stall Owner #13
Barn Raising II,III,IV NCM Supporter '13,'14,'16,'17,'19,'20 Bantayan Kids '13,'15,'17 GTMS ‘18
Join Date: Jan 2012
Location: Ypsilanti, Mi
Posts: 13,298
Thanks: 7,790
Thanked 2,641 Times in 1,956 Posts
Gameroom Barn Bucks: $425244
|
Nice craftsmanship
|
||||||
The Following User Says Thank You to Black94lt1 For This Useful Post: |
05-25-2019, 9:20pm | #4 | ||||||
Barn Stall Owner #327
NCM Supporter '16,'17,'19,'20 Bantayan Kids '13,'14,'15,'17 GTMS ‘18
Join Date: Jan 2011
Location: Zionsville,PA
Posts: 49,142
Thanks: 25,812
Thanked 21,887 Times in 8,906 Posts
Gameroom Barn Bucks: $5976008
|
|
||||||
05-25-2019, 9:23pm | #5 | ||||||
Sparkles Flambeaux
Barn Stall Owner #4 Barn Raising I,II NCM Supporter '13,'14,'15,'16,'17,'21 Bantayan Kids '13,'14,'15,'17
Join Date: Jan 2011
Location: Santa Fe, NM
Posts: 61,465
Thanks: 11,772
Thanked 33,024 Times in 14,164 Posts
Gameroom Barn Bucks: $17500122
|
Found a box for the book!
Mailing next week. |
||||||
The Following User Says Thank You to DAB For This Useful Post: |
05-26-2019, 9:53am | #6 | ||||||
Latin American Goat Roper
Barn Stall Owner #101 Bantayan Kids '13
Join Date: Nov 2009
Location: Orange Park Florida
Posts: 60,724
Thanks: 32,905
Thanked 11,563 Times in 5,702 Posts
Gameroom Barn Bucks: $1138393
|
That skived out section of the casting, what do?? weld it up and machine it out, or just use some kind of filler/glue/etc???
|
||||||
05-26-2019, 6:37pm | #7 | |||||||
Barn Stall Owner #327
NCM Supporter '16,'17,'19,'20 Bantayan Kids '13,'14,'15,'17 GTMS ‘18
Join Date: Jan 2011
Location: Zionsville,PA
Posts: 49,142
Thanks: 25,812
Thanked 21,887 Times in 8,906 Posts
Gameroom Barn Bucks: $5976008
|
Quote:
The picture shows the original sprocket that got against the outer bearing cage and as the steel sprocket wore, it "ate" the casting away. As seen in the replacement sprocket ( it's a plus 1 tooth) , it should be flat. Since I could get measurements off the sprocket, I made a "mirror image" of a bronze washer to replace the aluminum that was worn away. |
|||||||
The Following User Says Thank You to JRD77VET For This Useful Post: |
05-28-2019, 3:01am | #8 | ||||||
Barn Stall Owner #49
Join Date: Jan 2011
Location: People's Kollektive of Seattle
Posts: 25,970
Thanks: 20,917
Thanked 3,978 Times in 2,076 Posts
Gameroom Barn Bucks: $1025197
|
I love a good save like that!!!!
|
||||||
The Following User Says Thank You to SQUIRMIN VERMIN 84 For This Useful Post: |
|
|
Support the Barn: |
Download the Mobile App; |
Follow us on Facebook: |
||