|
Off Topic Off Topic - General non-Corvette related discussion. |
|
Share | Thread Tools | Search this Thread |
03-07-2024, 6:27pm | #1 | ||||||
A Real Barner
Join Date: Apr 2019
Location: North Carolina
Posts: 17,428
Thanks: 4,967
Thanked 24,020 Times in 9,995 Posts
Gameroom Barn Bucks: $315482
|
Ammco Brake Lathe Restoration
So I picked this up in August.
Had an Uncle Morty's spray can resto with plenty of metal and dirt under the paint. It leaked gear oil badly also. Wire wheel along with steel wool and oil to clean and protect any non painted surfaces such as adpaters and tools. Parts replaced: main switch, plug end, Led light, 4 oil seals, 6 bearings(motor included), shaft protection boots, one brass part in rotor feed box. Waiting for parts took as long as the resto. Oh we have those in stock.... And 4 days later they say the parts will ship in a month. The main drive pin was broken and it was 2 months to get a new one so I made one instead of waiting. Picked up a brake drum and rotor dial indicator pretty cheap. Welded on some large caster I had laying around so can push to back corner when not used. Pretty simple to restore it, strip and clean, paint everything and polish the shiney parts. Info on setting the bearing end play is non existant so some liberties were taken and past experience used to setup bearings and backlash. Overall it was in very good working condition when I got it. The only remaining issue is high speed rotor feed jumps, believe it's the grease I used is the issue(too thick). Not a big deal just takes an extra couple of minutes to turn a rotor using low speed. I did dial in the main hub adapters I will use for minimal runout on spindle and marked them. I need to get an extra shear gear and an extra main belt. Haven't cut a drum yet as I don't have any extras laying around at this point. I may have sold all my scrap iron couple of years ago which included a dozen plus drums. |
||||||
The Following 14 Users Say Thank You to Rodnok1 For This Useful Post: |
03-07-2024, 6:30pm | #2 | ||||||
A Real Barner
Join Date: Apr 2019
Location: North Carolina
Posts: 17,428
Thanks: 4,967
Thanked 24,020 Times in 9,995 Posts
Gameroom Barn Bucks: $315482
|
More pics
|
||||||
The Following 16 Users Say Thank You to Rodnok1 For This Useful Post: |
03-07-2024, 6:32pm | #3 | ||||||
Barn Stall Owner #112
Join Date: Apr 2022
Location: The Blue Ridge Mountains
Posts: 17,518
Thanks: 6,947
Thanked 4,809 Times in 2,838 Posts
Gameroom Barn Bucks: $500
|
Very cool. A machine like that was designed to last basically forever. Nice to see that you've done the required maintenance and repairs.
|
||||||
03-07-2024, 6:32pm | #4 | ||||||
Barn Stall Owner #103
Join Date: Feb 2017
Location: North Cackalaky
Posts: 25,782
Thanks: 12,056
Thanked 31,579 Times in 10,969 Posts
Gameroom Barn Bucks: $108939
|
I’m coming to you for resurface vs buy Chinese. Good job Rod 🍺
Have the; 2020 F150 73 Eldo, drums and disk 69 M1, drums and disk 2012 Jaq XJS all disk 2005 FGT all disk See ya sooner than later bro, and I’ll bring the shine/ booze etc… |
||||||
The Following 2 Users Say Thank You to MadInNc For This Useful Post: |
03-07-2024, 6:43pm | #5 | ||||||
A Real Barner
Join Date: Oct 2015
Location: America
Posts: 13,675
Thanks: 10,400
Thanked 6,409 Times in 2,194 Posts
Gameroom Barn Bucks: $1002182
|
Very talented.
|
||||||
03-07-2024, 6:47pm | #6 | ||||||
A Real Barner
Join Date: Apr 2019
Location: North Carolina
Posts: 17,428
Thanks: 4,967
Thanked 24,020 Times in 9,995 Posts
Gameroom Barn Bucks: $315482
|
I don't have the large rotor extension so may not be able to do larger truck rotors or the like unfortunately. I can't recall the max it does currently.
Drums suck to cut from the harmonics even with the silencer. I don't miss cutting those. Learned to cut drums at a friends grandfather's house as he had an drum only Ammco. We forgot to put the band on once... |
||||||
The Following User Says Thank You to Rodnok1 For This Useful Post: |
03-07-2024, 6:56pm | #7 | ||||||
A Real Barner
Join Date: Jan 2011
Location: Green Acres is the place to be...
Posts: 38,361
Thanks: 6,521
Thanked 24,282 Times in 11,013 Posts
Gameroom Barn Bucks: $8122190
|
Impressive.
|
||||||
03-07-2024, 6:59pm | #8 | ||||||
Barn Stall Owner #14/32
Join Date: Jan 2020
Location: IDK, IDC, IDGAF
Posts: 22,338
Thanks: 14,984
Thanked 13,461 Times in 5,144 Posts
Gameroom Barn Bucks: $4810
|
Sweet!
|
||||||
03-07-2024, 7:00pm | #9 | ||||||
10cm member
Barn Stall Owner #90125 NCM Supporter '19,'20
Join Date: Jan 2011
Location: Houston, Tejas, Estados Unidos
Posts: 83,487
Thanks: 38,118
Thanked 42,073 Times in 17,522 Posts
Gameroom Barn Bucks: $2621492
|
Very cool. Thread delivers, plenty of pics......nice work!
|
||||||
03-07-2024, 7:39pm | #10 | ||||||
Barn Stall Owner #55
Island14 Cardio Team
Join Date: Jan 2011
Location: A sympathetic, well-meaning, elderly man with a poor memory
Posts: 14,852
Thanks: 3,779
Thanked 9,241 Times in 4,399 Posts
Gameroom Barn Bucks: $23236
|
I can smell that machine running...
|
||||||
The Following User Says Thank You to ZipZap For This Useful Post: |
03-07-2024, 8:22pm | #11 | ||||||
A Real Barner
Join Date: Aug 2013
Location: sweatin' on the oldies
Posts: 13,921
Thanks: 8,306
Thanked 3,891 Times in 2,242 Posts
Gameroom Barn Bucks: $1000483
|
|
||||||
03-07-2024, 8:26pm | #12 | ||||||
Barn Stall Owner #327
NCM Supporter '16,'17,'19,'20 Bantayan Kids '13,'14,'15,'17 GTMS ‘18
Join Date: Jan 2011
Location: Zionsville,PA
Posts: 49,275
Thanks: 25,902
Thanked 21,959 Times in 8,932 Posts
Gameroom Barn Bucks: $5976008
|
Nice job
|
||||||
The Following User Says Thank You to JRD77VET For This Useful Post: |
03-08-2024, 7:20am | #13 | ||||||
That's MR Hole To You
Barn Raising I,II
Join Date: Oct 2009
Posts: 28,968
Thanks: 28,425
Thanked 227 Times in 133 Posts
Gameroom Barn Bucks: $3067
|
I put many hours on one of those back in the mid to late 70's.
|
||||||
03-08-2024, 7:39am | #14 | ||||||
A Real Barner
Join Date: Dec 2019
Location: Matthews, NC
Posts: 17,289
Thanks: 6,324
Thanked 21,917 Times in 9,230 Posts
Gameroom Barn Bucks: $311064
|
Nice job!
Not many shops cut rotors anymore nor do they put enough metal on a rotor for it to be turned. |
||||||
03-08-2024, 8:36am | #15 | ||||||
A Real Barner
Join Date: Dec 2011
Location: Down the Shore,New Jersey Elev.3 feet.
Posts: 18,826
Thanks: 4,637
Thanked 11,161 Times in 5,221 Posts
Gameroom Barn Bucks: $1007997
|
|
||||||
03-08-2024, 8:40am | #16 | ||||||
A Real Barner
Join Date: Jan 2012
Location: 1.Just because I'm paranoid doesn't mean people aren't out to get me...
Posts: 1,689
Thanks: 712
Thanked 710 Times in 365 Posts
Gameroom Barn Bucks: $530
|
I remember using that machine back in the early 70's
|
||||||
03-08-2024, 9:06am | #17 | ||||||
Vette Barn Crew
Join Date: Apr 2013
Location: Florida
Posts: 125
Thanks: 1
Thanked 78 Times in 41 Posts
Gameroom Barn Bucks: $1000702
|
Nice
The round carbide inserts do a nice job and are very cost effective. |
||||||
03-08-2024, 9:22am | #18 | |||||||
A Real Barner
Join Date: Sep 2021
Location: NYS Finger Lakes
Posts: 15,950
Thanks: 8,193
Thanked 10,277 Times in 4,324 Posts
Gameroom Barn Bucks: $500
|
Quote:
Built in mid-'80s: Electrical Discharge Machine, bought new in 1989: Eltee Pulsitron EDM, early-mid '80s era: Some of these hand tools have been sold, still have a lot left: |
|||||||
03-08-2024, 9:48am | #19 | ||||||
A Real Barner
Join Date: Apr 2019
Location: North Carolina
Posts: 17,428
Thanks: 4,967
Thanked 24,020 Times in 9,995 Posts
Gameroom Barn Bucks: $315482
|
I would have driven a truck over and purchased alot of your machines if I was closer. I'm a good 12 hrs away unfortunately.
|
||||||
The Following User Says Thank You to Rodnok1 For This Useful Post: |
03-08-2024, 10:05am | #20 | |||||||
A Real Barner
Join Date: Sep 2021
Location: NYS Finger Lakes
Posts: 15,950
Thanks: 8,193
Thanked 10,277 Times in 4,324 Posts
Gameroom Barn Bucks: $500
|
Quote:
I doubt I'll ever get rid of them, even for scrap. It will cost too much to move them, probably more than the scrap price is. We'll see. |
|||||||
|
|
Support the Barn: |
Download the Mobile App; |
Follow us on Facebook: |
||