PDA

View Full Version : Interior lights


navyndi2
01-05-2011, 6:14pm
ok this should be simple but it's kicking my rear, how the heack do i pull out the interior light bulbs, i can't seem to grip them with my fingers and I bought led replacements, tyi

:cheers:

wwomanC6
01-05-2011, 7:13pm
Good question? So I went out to see if i could get mine to come out. No joy. Did not want to pull on them to hard, as I would have to go get replacements. I thinking maybe a special puller tool maybe. :bilmem:Owners manual says for bulbs not listed see dealer. Not!

Even went to the Online Chilton Manual. Nothing. Dam.

navyndi2
01-06-2011, 12:16pm
I talked to the vendor I bought them from and he said the easiest way was to loop dental floss around them. Off to dental :)

wwomanC6
01-06-2011, 2:04pm
Dental floss, hun! Let me know if it works. :cheers:

:squirrelrun:

navyndi2
01-06-2011, 8:07pm
Dental floss totaly sux, worked with for about 30 minutes on one of the map light bulbs and nothing, tryed fishing line too, same results. Looked around and found a roll of 2" 3m masking tape, ended up wraping the bulb with that and it poped right out. Was a little cramped from spending that much time in the front of the car so i went to the back, used a set of gloves and poped those out and in, overall if i had used tape in the first place, probably could have done the whole car in under 15 minutes. Here's a few pic's..
Front Map lights http://i83.photobucket.com/albums/j309/navyndi2/0dba571a.jpg
Rear cargo lights
http://i83.photobucket.com/albums/j309/navyndi2/483f8d49.jpg
http://i83.photobucket.com/albums/j309/navyndi2/6191646d.jpg
Gloves and wraped up bulb
http://i83.photobucket.com/albums/j309/navyndi2/9ed008a0.jpg
hope this saves someone a little headache:cheers:

Omega Man
01-06-2011, 8:28pm
I have a small pair of needle nose vice grips with the tips wrapped in tape. Adjust the size of the pliers to the bulb size so you do not crush it.

Lemme look for a picture.

Omega Man
01-06-2011, 8:57pm
Check it:

http://i925.photobucket.com/albums/ad91/ClaymoreEnergy/71a90dc4.jpg


Make sure you do not crush the bulb. The pliers i have in the picture are fully closed with the jaws already adjusted.

hope this helps.

:cheers:

navyndi2
01-06-2011, 9:42pm
That would have worked, but I let someone borrow mine a few days ago and they have yet to return them. Now for the covers under the dash and hood do they pop off with a micro srcrewdriver?:cheers:

Omega Man
01-06-2011, 11:54pm
Yes, that will work fine. Just don't force them. That is how I did it.

navyndi2
01-07-2011, 10:57pm
chit, broke the under hood led and cause it didn't light, and i can't seem to get the under dash light covers off what's the trick?

Superstreet
01-10-2011, 4:07pm
We just replaced the interior bulbs with LED's. Example,the rear-view mirror bulbs: I used a rubber hose that had a slightly smaller inside diameter than the outside diameter of the bulb. I slid the hose over the bulb and the bulb came right out. :cheers:

Roadjet
01-25-2012, 2:22am
Seems to be a lot of work to get these bulbs out. What is the purpose?
Also does anyone no how to get info on the barn building event in may?

Roadjet
01-25-2012, 2:23am
:)Seems to be a lot of work to get these bulbs out. What is the purpose?
Also does anyone no how to get info on the barn building event in may?

wwomanC6
01-25-2012, 6:56am
:)Seems to be a lot of work to get these bulbs out. What is the purpose?
Also does anyone no how to get info on the barn building event in may?
If a light goes out, its logical to replace it! :dunno:

Barn Raising II event be held at NCM in Bowling Green Kentucky from the 24 to 27 of May. More info can be found here. :cert:

http://www.thevettebarn.com/forums/off-topic/20292-few-more-br-ii-details.html
http://www.thevettebarn.com/forums/off-topic/20018-we-did-everyone-inside-br-ii-go.html

Superstreet
01-25-2012, 9:42pm
:)Seems to be a lot of work to get these bulbs out. What is the purpose?
Also does anyone no how to get info on the barn building event in may?

The LED's broadcast a "cleaner" and brighter look to them. :cert:

Bucwheat
02-24-2012, 3:35pm
I didn't know these things were so hard to get out.Guess they will never fall out.

cma1
07-31-2012, 10:21pm
have you tried using the little fuse puller that is in the fuse box ?

flemingz
04-25-2013, 3:55am
Hello all please let me know that where can you buy interior lights for cars ? and can all cars have them ? I have a 2003 Oldsmobile alero and looking for your ideas,.

Metal Recyclers Brisbane (http://www.businesslistings.net.au/Metal_Scrap/Slacks_Creek/Metal_Biz__Brisbane_Metal_Recycler_Cash_for_Old_Cars__Scrap_Metals/34981.aspx)

wwomanC6
04-25-2013, 3:17pm
Have you checked at O'Reilly's or AutoZone or an online part store? I'm sure they have replacement lights and bulb. If not a dealer should have them.

If your adding more interior lights, you might need to take in to consideration the additional battery draw and plan that in to the mod.

Bucwheat
05-17-2013, 10:00am
I just took my foot well lights out to replace them with LED lights and I didn't have that much trouble ,guess I have a good grip.

slowrain
06-07-2013, 9:27pm
Seems to be a lot of work to get these bulbs out. What is the purpose?
Also does anyone no how to get info on the barn building event in may?

Same doubt here :dance::D:lol:

Bucwheat
07-12-2013, 3:55pm
I took the map lights out and replaced them with LED's ,what a difference,take a small flat blade screw driver and stick it in one of the holes on the lens,pops right out and the buld unplugs easy.

Eagleeye
03-09-2016, 6:40am
Same here...mine are the mini one with angle tip

Bucwheat
06-12-2016, 9:24am
Easier job than you think.

Eagleeye
06-27-2016, 8:41pm
That's how I got mine out...